Leave Your Message
Advanced Architectural Glazing Fasteners

Polycarbonate Roofing Screws For Curtain Wall Building

Precision-engineered fastening technology designed to neutralize high thermal expansion stresses, prevent dynamic shear cracking, and ensure watertight envelope integrity for modern translucent facades.

Commercial Status & Engineering Challenges

The structural transformation of translucent building envelopes and the fastening science supporting them

Thermal Expansion Mismatch Dynamics

Polycarbonate panels exhibit an unusually high linear thermal expansion coefficient, typically ranging from 0.065 to 0.070 mm/(m·K). Compared to steel framing (0.012 mm/m·K) or aluminum mullions (0.024 mm/m·K), multi-wall polycarbonate shifts substantially across diurnal temperature swings exceeding 40°C.

Standard static roofing screws cause severe localized hoop stress around penetrations. When temperature shifts trigger lateral panel expansion, rigid fastener shanks shear against the plastic hole edges, prompting radial micro-fissuring, stress crazing, and audible thermal 'popping'. Polycarbonate roofing screws engineered for curtain walls overcome this with precision reaming wings and vulcanized EPDM isolators that allow controlled lateral floating without sacrificing clamping force.

Dynamic Wind Uplift & Envelope Hermeticity

In modern high-span curtain wall buildings—such as exhibition pavilions, airport concourses, transit terminals, and automated logistics centers—facade elements endure severe dynamic cyclonic suction and cyclic positive gust pressures. Wind load forces transfer directly to fastener points as intense shear and tensile pull-out forces.

Conventional screws frequently suffer from fastener fatigue, thread striping in thin cold-rolled steel purlins, or premature washer degradation under prolonged UV exposure. Dedicated curtain wall polycarbonate screws leverage calibrated thread geometry with specialized flute-cutting edges, ensuring an airtight, water-impermeable seal against positive and negative pressures up to 3.5 kPa.

> 3.5 kPa
Wind Load Vacuum Rating
0.065 mm
Expansion Clearance / m·°C
25+ Years
Anti-Corrosion UV Resilience
0% Leaks
EPDM Vulcanized Integrity

Fastener Metallurgy & Bi-Metal Technology

Combining the corrosion immunity of austenitic stainless steel with the drilling power of carbon steel

Bi-Metal Friction Welding Architecture

In curtain wall projects, drilling directly through structural heavy-gauge steel supports (up to 12.5mm thickness) without pre-punching requires extreme drill point hardness. However, 400-series martensitic stainless steel lacks long-term atmospheric pitting resistance in industrial or coastal environments, while 304/A2/316 austenitic stainless steel is too ductile to penetrate structural purlins.

Our bi-metal self-drilling technology solves this via laser-controlled inertia friction welding. The hardened carbon steel tip pierces and taps structural steel subframes swiftly, while the shank and head—manufactured from premium grade 304 (A2) or 316 (A4) austenitic stainless steel—provide lifetime resistance against atmospheric corrosion, stress corrosion cracking (SCC), and thermal shear failure.

Thermally Decoupled Washer & Winged Point Design

When fastening translucent polycarbonate or multi-wall paneling to curtain wall framing, pre-drilling oversized holes on elevated scaffolding introduces steep labor costs and misalignments. Modern curtain wall screws incorporate integral breakout reamer wings positioned directly above the drilling flutes.

As the screw penetrates the polycarbonate, the reamer wings bore a neat thermal expansion hole (typically 8mm to 10mm diameter). Upon contacting the metallic substructure, the sacrificial wings sheer off instantaneously, allowing the self-tapping threads to grip the structural metal rigidly. Simultaneously, an oversized 19mm–29mm vulcanized bonded EPDM aluminum flange washer spreads the clamping pressure uniformly over the panel ribs, eliminating localized crush fractures.

In-Depth Application Curtain Wall Scenarios

Targeted solutions for intricate architectural geometries, daylighting atriums, and industrial facilities

1. Continuous Translucent Industrial Curtain Walls

Modern distribution warehouses and gigafactories deploy massive vertical runs of cellular multiwall polycarbonate sheeting to substitute for traditional insulated sandwich panels, introducing glare-free daylighting to plant floors. The polycarbonate roofing screws utilized in these applications must resist sustained vibrations from overhead bridge cranes, seismic lateral drift, and continuous internal wind turbulence while preventing rainwater penetration across 15-meter vertical expanses.

2. Skylight Atriums & Sloped Curtain Wall Enclosures

Transit terminal skylights and commercial gallerias blend roof glazing seamlessly into curtain wall facades. These low-slope, highly exposed configurations face prolonged UV radiation and stagnant water pooling. Screws configured with high-grade nylon cap heads and anti-aging EPDM gaskets prevent UV-induced washer hardening, ensuring no catastrophic water infiltration damages interior finishes or structural framing members.

3. Agricultural & Botanical Research Bio-Domes

Commercial greenhouse curtain walling demands specialized chemical and high-humidity resistance. The internal greenhouse atmosphere contains high moisture and fertilizer vapors, creating severe micro-climates. A2/304 stainless steel self-drilling screws with Ruspert 1000-hour salt spray barrier coatings provide uncompromising protection against corrosive chemical fumes without degrading polycarbonate panel clarity.

4. Acoustic & Blast Mitigation Transport Barriers

Solid polycarbonate sheets applied along highway acoustic walls and high-speed rail curtain buffers endure intense alternating acoustic pressures. Heavy-duty self-drilling hex flange screws distribute the rhythmic compression and suction forces across structural I-beams, mitigating cyclic metal fatigue and eliminating structural chatter.

Technical Specification & Installation Integrity

Scientific torque control and structural installation metrics to guarantee zero envelope failures

Torque-Controlled Fastener Driving

The primary root cause of polycarbonate curtain wall failure is over-torquing during installation. When contractors drive fasteners using uncalibrated impact wrenches, the excessive clamping load crushes internal multi-wall flutes, permanently distorts the thermal expansion gap, and splits the EPDM seal outward. Dahe recommends calibrated screw guns fitted with adjustable torque clutches (limiting seating torque between 4.5 Nm and 6.0 Nm depending on panel thickness). This ensures the EPDM seal is uniformly compressed to 30% of its initial thickness, guaranteeing a watertight bond without restricting lateral thermal sliding.

Furthermore, maintaining perpendicular driving alignment is critical. An angled drive cocks the washer flange, placing unequal edge pressure on the brittle polycarbonate matrix and leaving one side open to atmospheric moisture ingress. Our hex washer flange geometry is designed to seat flush across standard purlin profiles, providing positive visual confirmation of proper seating.

DaHe Industrial Growth & Milestones

Two decades of vertical integration, automated precision manufacturing, and global excellence

Foundation
2003

Foundation of the company

DaHe Industrial was founded in 2003, when the Chinese self drilling screw market was flooded with cheap, low‑quality products.

Against the trend, our founder Mr. Han set the company's sights on the mid‑to‑high‑end market, insisting on products that meet national standards.

Though our higher prices made us less competitive at first, our quality commitment never wavered.

Over three years, word‑of‑mouth built DaHe into a trusted brand symbolizing quality laying a solid foundation for growth.

Growth
2008

Our Growth

From 2005 to 2007, we ran a small workshop.

In 2008, Mr. Han purchased 50 acres in his hometown and built our first factory – Handan Shan You Fasteners.

Equipment imported from Taiwan, with technical support from Taiwanese and Japanese friends.

Upon startup, monthly output reached 50 tons, annual 6,000 tons making us a leader in China's self‑drilling screw industry in terms of precision and stability.

development
2014

Our Development

As the domestic economy boomed, market demand soared and supply fell short for years.

Our brand gradually rose to a top national level, and by then, our technology had matured to the point where we surpassed well-known Taiwanese and other leading brands.

In 2014, we acquired a second plot of land and built our second factory – Shenzhen DaHe Industrial Co., Ltd. Hebei Branch.

full vertical
2014

Full Vertical Integration

The second factory covers 200 acres, with a monthly output of over 1,500 tons and an annual output of 20,000 tons. Its launch marked the first in the industry to bring all processes in‑house – from raw material to packaging, with no external outsourcing.

This completed our full industrial chain and closed‑loop quality control.

Since then, we have become the leading brand nationwide in both market share and reputation.

production
2019

Phase III Smart Manufacturing & Green Production

We then intensified new product development, smart system and ERP implementation, and green production investments.

In 2019, we purchased 300 acres for our third factory (Hebei Xilide Metal Manufacturing Co., Ltd.), which began operation that same year, along with a 6,000‑ton three‑story intelligent warehouse.

The launch marked the world's first fully automated self‑drilling screw production line – continuously advancing in intelligence, automation, and environmental sustainability.

leader
2026

Today: A Global Leader

To date, our monthly output has reached 6,000–7,000 tons, with an annual output of 80,000 tons.

We have grown into the world's largest, highest‑yield, and most advanced manufacturer of self‑tapping and self‑drilling screws, equipped with the most comprehensive quality inspection equipment in the industry.

future
Future

Our Future

Over the years, we have grown globally, serving customers across five continents. We lead with cutting-edge technology — automated production lines, precision testing, and continuous R&D. At the same time, we are committed to environmental responsibility: eco-friendly coatings, energy-saving processes, and waste reduction are core to our operations.

We deliver durable, high-performance screws that solve real‑world challenges — wherever our customers are.

Our journey continues, and we look forward to growing with partners worldwide.

OUR TEAM

At present, Dahe Group has nearly 900 dedicated employees driving fast, high-quality production

50+
QC team members
20+
R&D personnel
90+
Management staff
100+
Technical backbone
30+
Logistics personnel
600+
Frontline employees

Global Reach & Vision

Expanding the frontiers of fastening technology across international building sectors

International Start

Before 2013, we focused on domestic sales.

In 2019, Alan (the chairman's son) returned, built our export team, and actively entered global markets. Export revenue has now approached 40% of the company's total output value.

Our Vision

We will continue to deepen our expertise in self-drilling screws, always targeting the mid-to-high-end market.

Our vision is to become a globally recognized partner and the most valuable factory in our niche — dedicated to innovating roof screws, metal screws, window screws, decking screws, wood screws, timber screws, and color screws.

Our Mission

To help employees achieve their life dreams and assist customers in achieving their strategic goals.

Global Partners

Trusted by engineering firms, curtain wall contractors, and industrial builders across continents

Partner 1
Partner 2
Partner 3
Partner 4
Partner Standard
Partner 6
Partner 7

Join DaHe

JOIN US

At DaHe, we are more than a manufacturing company — we are a team committed to intelligent manufacturing, sustainable development, and creating long-term value for customers worldwide.